Click image to view full size image
Model Number: ST106-03-23
Brand Name: eoutil
Key Specifications/Special Features:
ST106 Four LEDs Indicators AC Warning Stud Finder DetectorDetecting wood and metal stud up to 3/4 in (19mm)Detecting AC Live wire up to 3 in(76mm)Auto calibration stud detection4 LEDs visual and audio indicatorNet weight:71.1g
Size:55*28.3*130mm
Product Specification
The stud finder with AC warning locates wood and metal stud edges as deep as 3/4 in.(19mm) in the walls. The AC warning detection automatically detects and alerts the use of live AC wires. When AC live wires are detected, the AC warning LED will illuminate.
Surroundings Condition For Use
- Temperature: 5℃ to 40℃
- Max. humidity 90%
- Use only indoors
Power supply
Requires one 9 volt battery to operate (battery not included).
Battery installation
1.Open the battery cover on the back of the unit.
2.Install a DC9V battery (6F22) into the compartment .
3.Replace the battery door ; battery life is approximately 10 hours.
Using the detector
1. Position the unit flat against the wall.
2. Press on/off button and continue to hold in.
3. Slowly slide unit horizontally across the wall, right or left. As you begin to approach a stud, the yellow LEDs will light, from bottom to top.
4. Mark the spot when the top red LED lights and the beep sounds.
5. Continue scanning beyond the marked spot until the yellow LEDs go out.
6. Slide the unit in the reverse direction. Mark the second spot when stud detects again.
7. The middle of the stud is centered between the two marks.
AC warning
AC warning works continuously. When live AC voltage is detected, the AC Warning LED will illuminate. Always turn off the power when working near electrical wires.
CAUTION: AC wires deeper than 2 in.(51mm) from the surface may not be detected. Be especially careful when live AC present.
The stud finder with AC warning locates wood and metal stud edges as deep as 3/4 in.(19mm) in the walls. The AC warning detection automatically detects and alerts the use of live AC wires. When AC live wires are detected, the AC warning LED will illuminate.
Surroundings Condition For Use
- Temperature: 5℃ to 40℃
- Max. humidity 90%
- Use only indoors
Power supply
Requires one 9 volt battery to operate (battery not included).
Battery installation
1.Open the battery cover on the back of the unit.
2.Install a DC9V battery (6F22) into the compartment .
3.Replace the battery door ; battery life is approximately 10 hours.
Using the detector
1. Position the unit flat against the wall.
2. Press on/off button and continue to hold in.
3. Slowly slide unit horizontally across the wall, right or left. As you begin to approach a stud, the yellow LEDs will light, from bottom to top.
4. Mark the spot when the top red LED lights and the beep sounds.
5. Continue scanning beyond the marked spot until the yellow LEDs go out.
6. Slide the unit in the reverse direction. Mark the second spot when stud detects again.
7. The middle of the stud is centered between the two marks.
AC warning
AC warning works continuously. When live AC voltage is detected, the AC Warning LED will illuminate. Always turn off the power when working near electrical wires.
CAUTION: AC wires deeper than 2 in.(51mm) from the surface may not be detected. Be especially careful when live AC present.
Shipping Information:
- FOB Port: Fuzhou
- Lead Time: 35 - 45 days
- HTS Code: 9031.80.90 90
- Dimensions per Unit: 21.6 × 13.5 × 4 Centimeters
- Weight per Unit: 0.142 Kilograms
- Units per Export Carton: 80
- Export Carton Dimensions L/W/H: 44 × 37 × 50 Centimeters
- Export Carton Weight: 11.3 Kilograms
Main Export Markets:
- Asia
- Australasia
- Central/South America
- Eastern Europe
- Mid East/Africa
- North America
- Western Europe